Differences

This shows you the differences between two versions of the page.

--- fr:rhino:advancedfilleting [2020/08/14]
127.0.0.1 external edit
+++ — (current)
@@ Line 1: / Line 1: @@
-====== Advanced Filleting ======
-> **Summary:** //There are situations where the automatic filleting tools in Rhino may fail. This page contains tutorials that show how to manually get the desired results.//
-**Contact:** [[jb@mcneel.com|John Brock]] or [[pascal@mcneel.com|Pascal Golay]]
-======The two primary commands for filleting surfaces in Rhino are:======
-====FilletEdge:====
-  * Creates a tangent surface between multiple polysurface edges (joined) with optional varying radius values, trims the original faces, and joins the resulting surfaces together.
-  * Is not limited to just two surfaces
-  * Can fill in corners between adjacent fillets
-  * Is limited to exactly three surfaces meeting at a point
-  * The radiuses used can not be so large that they overlap each other and completely consume any surface they are following.
-====FilletSrf:====
-  * Creates a tangent surface between two surface edges (joined or not) with a constant radius, and optionally trims and/or extends the original surfaces.
-  * Works on exactly two surfaces at a time
-  * Does not fill in corners between adjacent fillets
-======What if they don’t work?======
-\\
-| **[[FourSrf|Four Surfaces]]** |
-| [[FourSrf|{{:legacy:en:step_8.jpg}}]] |This example will show you how to manually fillet a corner where 4 planar surfaces meet at a single point. |
-| //Last update: january 19th 2007// |
-\\
-| **[[FiveSrf|Five Surfaces]]** |
-| [[FiveSrf|{{:legacy:en:5srfEnd.png}}]] |This example will show you how to manually fillet a corner where 5 planar surfaces meet at a single point. |
-| //Last update: january 22nd 2007// |
-\\
-| **[[OverlapSrf|Overlapping surfaces]]** |
-| [[OverlapSrf|{{:legacy:en:OverlapStart.png}}]] | [[OverlapSrf|{{:legacy:en:OverlapEnd.png}}]] |This example will show you how to manually fix two overlapping fillet surfaces. |
-| //Last update: january 19th 2007// |
-\\
-| **[[PocketSrf|Short walled pocket]]** |
-| [[PocketSrf|{{:legacy:en:PocketStart.png}}]] | [[PocketSrf|{{:legacy:en:PocketEnd.png}}]] |This example will show you how to manually fillet a pocket with the walls are too short for the desired radius. |
-| //Last update: january 22nd 2007// |
-\\
-| **[[SmallToBig|Existing small radius]]** |
-| [[SmallToBig|{{:legacy:en:SmallToBigStart.png}}]] | [[SmallToBig|{{:legacy:en:SmallToBigEnd.png}}]] |This example will show you how to use a large radius fillet when a small radius fillet already exists. |
-| //Last update: january 22nd 2007// |
-\\
-| **[[TanCylinders|Tangent Cylinders]]** |
-| [[TanCylinders|{{:legacy:en:TanCylindersEnd.png}}]] |This example will show you how to fillet two stacked cylinders that share a tangent side. |
-| //Last update: january 22nd 2007// |
-\\
-| **[[OverlapBoxes|Overlapping boxes]]** |
-| [[OverlapBoxes|{{:legacy:en:OverlapBoxesEnd.png}}]] |This example will show you how to fillet the shared edges of two overlapping boxes.|
-| //Last update: january 22nd 2007// |
-\\
-| **[[FourSrfReverse|Mitch's First Challenge]]** |
-| [[FourSrfReverse|{{:legacy:en:Mitch1Done.jpg}}]] |Here's an example sent in by Mitch Heynick.  Mitch writes: Fillet all vertical edges plus the base with a radius of 10.  Fillet the horizontal inside edges near the top at 5. --Mitch|
-| //Last update: january 25th 2007// |
-\\
-| **[[FourSrfAngle|Mitch's Second Challenge]]** |
-| [[FourSrfAngle|{{:legacy:en:Mitch2_07b.jpg}}]] |Here's another example sent in by Mitch Heynick.  I'll admit, this one stumped me but Pascal figured it out. Mitch writes: Fillet all the surfaces except bottom with a constant radius of 5.  --Mitch|
-| //Last update: january 30th 2007// |
-\\
-----

McNeel Wiki

Site Tools

Differences

Page Tools